WARF: P160142US01

Inverter for Common Mode Voltage Cancellation


Bulent Sarlioglu, Di Han

The Wisconsin Alumni Research Foundation (WARF) is seeking commercial partners interested in a novel inverter topology for motor drives that eliminates problems with common mode voltage (the voltage difference between the power source ground and the neutral point of a three-phase load).

Advantages of this technology include reduced electromagnetic interference emissions, elimination of CM filters, increased machine reliability and extended bearing life.
OVERVIEWIn a drive system, a voltage source inverter (VSI) may be used to transfer real power from a DC power source to an AC load. Conventional VSIs consist of two or three phase-legs, each of which is a series connection of two semiconductor switches.

During normal operation, the output potential of each phase-leg with respect to ground is continuously switched between a positive and a negative DC bus potential based on a pulse width modulation of the switches. As a result, undesired common mode (CM) voltage imposed on the load also exhibits six step-changes during each switching cycle. Each step-change induces a charging or discharging current into the parasitic capacitances between load and ground that leads to issues such as electromagnetic interference emissions, inverter losses and motor damage. The bearing damage in inverter-driven motors is mainly caused by the shaft voltage and the bearing currents created by CM voltage.

CM chokes and filters may be used to mitigate the CM voltage-induced issues. However, since CM chokes have to block a significant amount of CM voltage, they are bulky and constitute a large portion of the product cost.
THE INVENTIONUW–Madison researchers have developed inverter topology in which the CM voltage is 100 percent cancelled. Instead of the two switches in series (as found in conventional designs) the new ‘balanced inverter’ features three switches in series wherein the upper and lower switches of each phase-leg are rated at half the DC bus voltage.

The half-rated switches turn on and off simultaneously. The middle switch of each phase-leg operates complementarily with the other two, and is rated at the full DC bus voltage. This essentially replaces one full voltage-rated switch with two half-rated switches on the top and bottom of each phase.

The new topology cancels the total CM voltage by generating two equal-amplitude, opposite-signed CM voltages on the two sets of three windings. Hence, the whole machine remains at ground potential, and no current will flow to the ground. In addition, to take advantage of the six AC terminals of the balanced inverter, the three phase motor windings need to be equally separated as two sets of windings. This can be done by reconfiguring the series connected machine windings, which is particularly convenient for dual-voltage 9-lead machines.
  • For use in electric motor drives including industrial and commercial drives, traction drives for hybrid/electric vehicles, generator and motor drives for aircraft and vessels
  • Cancels CM voltage generation
  • Reduces electromagnetic interference (EMI) emissions
  • Eliminates CM filters
  • Eliminates ground leakage current and corresponding losses
  • Prevents false triggering of ground fault protection
  • The shaft voltage and bearing current on the electric machine can be eliminated for increased reliability and extended bearing life.
STAGE OF DEVELOPMENTThe researchers have simulations and calculations indicating 100 percent reduction of CM voltage peak amplitude and number of step changes, compared to a conventional inverter. The researchers have engineering prototype and experimental data showing up to 40 dB reduction in CM EMI emission.

The development of this technology was supported by WARF Accelerator. WARF Accelerator selects WARF's most commercially promising technologies and provides expert assistance and funding to enable achievement of commercially significant milestones. WARF believes that these technologies are especially attractive opportunities for licensing.
For More Information About the Inventors
Related Technologies
  • To learn about innovative flux-switching permanent magnet (FSPM) machines developed by Prof. Sarlioglu, see WARF reference numbers:
  • P150249US01
  • P140405US01
Contact Information
For current licensing status, please contact Michael Carey at or 608-960-9867.
The WARF Advantage

Since its founding in 1925 as the patenting and licensing organization for the University of Wisconsin-Madison, WARF has been working with business and industry to transform university research into products that benefit society. WARF intellectual property managers and licensing staff members are leaders in the field of university-based technology transfer. They are familiar with the intricacies of patenting, have worked with researchers in relevant disciplines, understand industries and markets, and have negotiated innovative licensing strategies to meet the individual needs of business clients.